Search:

Type: Posts; User: DONVS

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    17,983

    Completely understood. Advanced will inform you...

    Completely understood. Advanced will inform you as to which type your cht is. Just call Shaun and ask.
  2. Replies
    5
    Views
    17,983

    John, If you order the CHT probe directly from...

    John,
    If you order the CHT probe directly from Advanced you can be sure that you will receive the correct product.
  3. Thread: Inflight Reboot

    by DONVS
    Replies
    2
    Views
    50,738

    If you are using the TCW backup and wired it...

    If you are using the TCW backup and wired it direct to ground it is easy enough to install a switch to turn off the backup battery. I am not sure if the system will reboot correctly while airborne...
  4. Yes, that is correct

    Yes, that is correct
  5. The Ray Allen sensors are wired to the AFS system...

    The Ray Allen sensors are wired to the AFS system only. The trim motors are wired to the trim control board. The sensor wires are red(+) green (signal) blue(-). The sensor positive and negative get...
  6. Thread: XM radio support

    by DONVS
    Replies
    4
    Views
    12,212

    Buy a cheap XM tuner that has an output via patch...

    Buy a cheap XM tuner that has an output via patch cable with a 2,5 plug on it and wire this into your audio panel. This will not give you volume control for the radio individually but it works for...
  7. Replies
    4
    Views
    10,144

    Wow. Glad mine was just the connector problem.

    Wow. Glad mine was just the connector problem.
  8. Thread: Shunt Question

    by DONVS
    Replies
    4
    Views
    9,703

    I put mine before the ANL Limiter. Works fine...

    I put mine before the ANL Limiter. Works fine there. It would be hard to damage the shunt.
  9. Replies
    4
    Views
    10,144

    The most likely problem is that the 480 is not...

    The most likely problem is that the 480 is not seated into its mount far enough. This is a common problem with the 480. Everything works except the items hooked to connector 5. Just crank the...
  10. Thread: % power IO-360

    by DONVS
    Replies
    9
    Views
    24,674

    And maybe one for the IO360 200HP Angle valve TIA...

    And maybe one for the IO360 200HP Angle valve TIA Don VS
  11. Replies
    24
    Views
    302,699

    I would like to see more information for dual...

    I would like to see more information for dual screen set-up. Things like should the screens be plugged together when doing the mag cal? what about when doing the fuel tank cal etc Thanks. Don
  12. Thread: ADS-B Weather??

    by DONVS
    Replies
    57
    Views
    78,257

    Trevor, What about us 480 users? If you can...

    Trevor,
    What about us 480 users? If you can eliminate the serial for the 430/530 is it also possible for the 480?
  13. Thread: Winds aloft

    by DONVS
    Replies
    21
    Views
    26,173

    Make that My method

    Make that My method
  14. Thread: Winds aloft

    by DONVS
    Replies
    21
    Views
    26,173

    View Post

    <y ,ethod also changed both the IAS and the altitude .
  15. Thread: Winds aloft

    by DONVS
    Replies
    21
    Views
    26,173

    Larry I guess I do things the hard way. Your way...

    Larry I guess I do things the hard way. Your way is much faster. Don
  16. Thread: Winds aloft

    by DONVS
    Replies
    21
    Views
    26,173

    I installed flush ports and the fix was not that...

    I installed flush ports and the fix was not that difficult. I removed the screw on connection, drilled out the port to allow the Van's pop rivet to be installed. Drove out the mandrel and cleaned all...
  17. Thread: Winds aloft

    by DONVS
    Replies
    21
    Views
    26,173

    Trevor and Sharpdoug, Your indicated airspeed as...

    Trevor and Sharpdoug,
    Your indicated airspeed as checked during an ifr cert does not take into account static system errors other than leaks. If you have flush ports or any other mounting issues...
  18. Replies
    16
    Views
    23,033

    Trevor, That wire should be able to handle the...

    Trevor,
    That wire should be able to handle the current that the starter motor draws. That would be quite a bit more than the alternator puts out.
  19. Replies
    3
    Views
    7,864

    Brian Gerdes at 714 525-7545 of Gill Ross at 951...

    Brian Gerdes at 714 525-7545 of Gill Ross at 951 736-3097 Both are certified repair stations and both will come to you. They both give cash discounts and have no issues working on experimental AC
  20. Replies
    1
    Views
    5,612

    Darwin, I used the same hub in my 7 when it was...

    Darwin,
    I used the same hub in my 7 when it was equipped with BMN stuff. I am currently installing a dual 4500 system in the 7and am using the hub again. Just be careful that Tim does not talk you...
  21. Replies
    7
    Views
    11,191

    Scott, Yes . All three ribs needed to be...

    Scott,
    Yes . All three ribs needed to be trimmed. The panel is based on the three piece affordable panel so I also had to cut the mount to move the radio stack to the left. Lots of work but it is...
  22. Replies
    7
    Views
    11,191

    Darwin, This is my 7 with two 4500's 55

    Darwin,
    This is my 7 with two 4500's

    55
  23. Replies
    7
    Views
    11,191

    Darwin, Go to Steinair and click on custom...

    Darwin,
    Go to Steinair and click on custom panels. Scroll down to the rv6,7,9 area and look at the third panel down on the left, It has two 4500's a radio stack and a trutrak efis. It is owned by...
  24. Replies
    4
    Views
    8,877

    And you can not use the poe for power. You will...

    And you can not use the poe for power. You will also need the xm power cable. No one makes a POE hub that will run on 12 volts.
  25. Thread: OAT probe ins

    by DONVS
    Replies
    2
    Views
    8,047

    That would be the nut side, Darwin.

    That would be the nut side, Darwin.
Results 1 to 25 of 27
Page 1 of 2 1 2