Rob, I have a single AFS-5600 with Garmin 430W, 327 transponder, SL-30, ARINC module with AFS autopilot programmer.
What is the best route to get to 2020 compliance? Wiring diagram?
Alton...
Type: Posts; User: AltonD
Rob, I have a single AFS-5600 with Garmin 430W, 327 transponder, SL-30, ARINC module with AFS autopilot programmer.
What is the best route to get to 2020 compliance? Wiring diagram?
Alton...
Can anyone tell me how to add additional categories to the maint. file?
Rob, I have a single screen setup and I have run out of serial ports.
How about you guys developing a box to take the ethernet connection and allow 4 more RS232 inputs? I am not really wanting to...
I watched the video of loading a flight plan from the AOPA flight planner onto a SD card and then loading onto the AFS-unit. I am guessing the AOPA software no longer supports export to the GPX...
Rob, is the number of lines still at the same limit as with the AFS-3500? 12 I think it was?
I have discovered my issue with sometimes intermittent operation of the Slick RPM sensor. Now, I need some long term help.
Ever so often, the RPM indication becomes intermittent. I always check...
DITTO. The missed for the ILS approach. The transition from ILS back to GPS guidance for the holding pattern.
https://lh6.googleusercontent.com/-hzoaKLnCjzQ/TlLvTphtthI/AAAAAAAAABo/iHjPqaoOqN8/s512/amps%252520readouts%252520004.jpg
I put a shunt on the alternator and a HAL effect transducer on the main Bus.
From that, I get alternator output and mainbus draw. Subtract and you have what is going to the battery.
Highway in the sky.
you can assign one of the 4 aux inputs to act as one of the panel buttons. I have button one assigned to a button on the stick to change pages and acknowledge alarms/alerts.
Calibration menu, #34...
yes, switch is not needed.
I know the Wx Worz receiver has XM audio. How do you control the channels? Is this done through the AFS-3500? Looking for some flying tunes.
I have an AFS-3500. The file date of the ARINC software is 6-16-10. Is this the latest?
What will be new with teh ARINC/GPS interface?
Question: If I get the MFD slave, do I get the extraRS232 ports?
Sounds like a good excuse to buy a second screen, upgrade my existing one to SV, and add ADSB.
OK, I am thinking I do not have any available RS232 channels. I have a SL30, encoder out, Garmin 430W, and Arinc429 converter for the AFS autopilot. How can I use the Navworx ADS-B receiver?
I...
Mine did the same thing. I tywrapped the wires so they could not flop in the airflow under the cowl where they connected to the harness. Crimped the spade connectors just a little more with neddle...
RV7A
I don't really remember the air speed, but it should have been ~150 KIAS.
No auto pitch trim
I'll have to check the torque setting. Is this the programmer head or the AFS setting?
Manually...
I didn't see any warnings on the programmer head. I did feed in some down trim and it did not happen again. I have seen the "Low air speed" in the past so I know where to look. I have never seen...
makes sense. I don't remember what my max speed setting is. I'll bump it up. I love the AP. I am still in phase 1. I have been practicing the GPS approach into my home base, 0J6. It is so cool...
Today, I was at 10,500 MSL and dialed up a decent @ 1000 fpm, target 2500 ft. I have a legacy 3500 and an Advanced programmer (aka trutrak). When I first started the decent, about every 15 seconds,...
Thanks. That is just what I needed.
Can anyone tell me how to upload a GPS file from the data file to google earth to get the fancy track pictures?