Search:

Type: Posts; User: johninreno

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    6,099

    Oops!

    That works for me too. I must have pulled v16 by mistake.

    john
  2. Replies
    2
    Views
    6,099

    AFS Map data for non-s cpu

    I started to update the files for November 12 thru December 10 and noticed that the full download link shows the AF2* files instead of AFS*.

    The map only link points to AFSMAPUS.AFM...
  3. Replies
    8
    Views
    17,535

    Added diode for 5 volt signal and changed input...

    Added diode for 5 volt signal and changed input to pin 32. No joy. I am looking for an "Aha" moment where all of the symptoms come together.

    Symptoms in cruise:
    RPM +/- 50
    Noisy EGT and CHT...
  4. Replies
    4
    Views
    11,758

    Thanks - I haven't seen the warning again but I...

    Thanks - I haven't seen the warning again but I will turn it off the next time I'm in the calibration menu.
  5. Replies
    4
    Views
    11,758

    Confused again! I don't think I have an external...

    Confused again! I don't think I have an external backup power attached to pin 15. My system is EFIS and EMS with internal backup batteries. I looked at the .ALD file again and it has some data from...
  6. Replies
    4
    Views
    11,758

    AUX VOLTS warning message

    On a recent 2 hour flight I got a, "AUX VOLTS", warning message about 3/4 of the way through the flight. I have searched the manual and the forums for a possible explanation with no luck.
    ...
  7. Replies
    8
    Views
    17,535

    Just a quick update. Adding a ground from the...

    Just a quick update. Adding a ground from the Pmag to the airframe brought back the tach signal but it still oscillates as before. The next step will be to try a 5 volt signal to pin 32. I will...
  8. Replies
    8
    Views
    17,535

    Tach signal

    The 3500 serial numbers are 60281 and 60282.

    The installation is dual P-Mags and the sensor is on pin 33. When I was getting ready for the first flight in July of 2013, the Pmags were refreshed...
  9. Replies
    8
    Views
    17,535

    My tachometer finally died completely. I have...

    My tachometer finally died completely.

    I have tried the LCOM filter, ran a new shielded sensor wire, and re-routed the P Lead wires with no joy. I have learned to live with the oscillation and...
  10. Replies
    8
    Views
    17,535

    AFS 3500 Phase I test issues

    I am seeing an RPM display that is useable but it oscillates +/- 50 RPM in cruise. I have the constant speed prop set to 2350 confirmed by an optical tach on the glare shield and the RPM display...
  11. Replies
    7
    Views
    12,491

    A very timely reminder. I will close the front...

    A very timely reminder. I will close the front skin on my "slow build" RV9A on Tuesday. Put new clock batteries in both screens today while it was still easy to access the top.
  12. Replies
    1
    Views
    6,050

    HAL effect and 2 AF3500

    Just getting everything going and the wiring and sensors look good so far. I have EFIS on the left and EMS on the right with the latest software - V70307-MV15 and the latest map files. Dual...
  13. Replies
    1
    Views
    7,502

    Restart Project

    I am restarting a stalled project. I have 2 AFS3500, one EFIS and one EM with software version 5.5.7-MV9. I should have all the engine probes and I know that I got a hall sensor to handle a dual...
Results 1 to 13 of 13