Search:

Type: Posts; User: BSteeves

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    14,969

    AFS Comm Wire Schematic

    Hello. I currently have 3 5600 screens, GMA240 Audio and a gtn650. Want to add in a surface mount AFS comm so that I will have two Comm's.

    Curious how to wire in this second com to the current...
  2. Replies
    6
    Views
    9,866

    Shawn, I do plan to work on the connections again...

    Shawn, I do plan to work on the connections again this evening and just redo them. However, this does not explain also why the engine information is doing the same thing. Cannot be that every...
  3. Replies
    6
    Views
    9,866

    I did disconnect the 5500 from the ethernet port...

    I did disconnect the 5500 from the ethernet port and did get the same results. I also did do the V12 software upgrade so went and checked all the settings and they were all good. Do not think this...
  4. Replies
    6
    Views
    9,866

    Engine Monitor and VPX cutting out

    I have 3 EFIS Screens, 2 5600 and 1 5500 installed with a VPX-Pro. My middle screen is 5500 and has the engine monitor board and where the VPX info is connected through. This last week I was up for a...
  5. Replies
    1
    Views
    5,905

    Two 5000 don't match heading

    I have two 5600 screens each connected to its own magnetometer. Both have been calibrated a few different times but I can never get them to match up. Is it possible to get both screens showing the...
  6. Replies
    8
    Views
    11,862

    Hello Rob. Sent you an email yesterday and want...

    Hello Rob. Sent you an email yesterday and want to make sure you received it. Also, I notice the newest version for download on the site is v8..... and the one I have is a v9. Can I use the V8 or...
  7. Replies
    8
    Views
    11,862

    Email sent

    Email sent
  8. Replies
    8
    Views
    11,862

    SW-X9.4.48-MV16 Os-1 FS-1 BB-3 ??? - 1.1.0...

    SW-X9.4.48-MV16
    Os-1
    FS-1
    BB-3
    ??? - 1.1.0
    Net 6.3
  9. Replies
    8
    Views
    11,862

    Magnotometers/AHRS

    I have 2 AFS-5600's with the red box Magnotometer/AHRS units. The units are located in the rear empennage area near the top.
    My issue is that when I make a right turn over 45 degrees and then level...
  10. Replies
    4
    Views
    7,921

    No problem. I think that is it, the OAT. This...

    No problem. I think that is it, the OAT. This EFIS does have its own but it did stop working. Will check the connections to see if that was it and then see if that solves the issue.

    Thanks for...
  11. Replies
    4
    Views
    7,921

    I did check the settings and all 3 Efis's have...

    I did check the settings and all 3 Efis's have the synthetic vision turned on and the TAWS is ON, and all three have the TAWS Airspeed shutoff to 100.

    As for the TAS kts. when the other Efis's...
  12. Replies
    4
    Views
    7,921

    EFIS Display- TAS and WS

    On my Co-pilot 5600, the TAS and wind direction, Speed, and XW do not display anything. On the pilot 5600, they are displaying just fine.

    Each EFIS is has AHRS, Piot/Static, and AOA connected.
    ...
  13. Thread: RS232 Imputs

    by BSteeves
    Replies
    3
    Views
    8,166

    I have the FreeFlight installed to the right...

    I have the FreeFlight installed to the right screen as you show above. Have the Settings in the EFIS on that port to ADSB 57K. Wondering if this is correct as I am not getting anything when I goto...
  14. Replies
    1
    Views
    6,764

    RPM not displaying

    I have a lightspeed Plasma III and one mag on a Lycoming IO540. The engine harness is installed with the rpm wires going directly to the mag as instructions show.

    The RPM reads fine when both the...
  15. Replies
    4
    Views
    8,817

    Thanks Bob. I was not aware that the AFS screens...

    Thanks Bob. I was not aware that the AFS screens had auto dim on them. I will have to just try it and see how it goes and if needed work on a solution then.

    Appreciate the help.

    Brian
  16. Replies
    4
    Views
    8,817

    Dimming the Screens

    I am just in the stage of wiring and installing my avionics and curious about dimming. I will have 2 5600's and 1 5500 screens and was curious if you need to dim all screens independantly or when...
  17. Thread: RS232 Imputs

    by BSteeves
    Replies
    3
    Views
    8,166

    RS232 Imputs

    I am installing 2 5600's and 1 5500 in a RV10 and was wondering about RS232 inputs. One for example would be the carbon monoxide warning to display on the EFIS instead of using the LED warning...
Results 1 to 17 of 17