Search:

Type: Posts; User: Frank D

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    692

    The Early 5600s apparently do not support the...

    The Early 5600s apparently do not support the Dynon SV-network. I am running the current software.
  2. Replies
    3
    Views
    692

    5600T AP Servo Compatibiity

    I have an early model AF-5600T. It has the second generation processor sold from 2013-2022, but has the older baseboard. BB version 6. Can I utilize any of the Dynon components? AP servos, AP...
  3. Replies
    1
    Views
    4,027

    GRT Safe Fly GPS with 4500s

    Hello, I have a Safe Fly WAAS GPS left over from another project. What GPS1 configuration would be compatible? The GPS has the following output:

    Serial Port Default Pins
    Serial Port 1 Out 4800...
  4. Thread: 73102 AF-GPS

    by Frank D
    Replies
    6
    Views
    12,986

    73102 afs gps

    OK, than I have it wired correctly. I have it on serial 4. Serial 4 set to 73102 AFS GPS, and GPS/NAV1 Data Source set to serial 4.

    How do I trouble shoot from there?

    Thanks,
    Frank
  5. Thread: 73102 AF-GPS

    by Frank D
    Replies
    6
    Views
    12,986

    Hi Shawn, I am having the same problem, where my...

    Hi Shawn, I am having the same problem, where my 4500 is not recognizing the AF-GPS. It is on Serial 4 and set up as gps source 2. Should the power be 12V or is it a step down v? The drawing seems...
  6. Replies
    1
    Views
    8,408

    Avidyne IFD540 Interface

    Do you have a schematic or document for the interface for the IFD5440 with the AF 5000 series (ARINC, AP, TXP, ADSB...)?
    Thanks
    Frank
  7. Replies
    8
    Views
    14,292

    It connects via the SV Network to the 5400.

    It connects via the SV Network to the 5400.
  8. Replies
    3
    Views
    46,413

    I believe I am seeing these pages, but have no...

    I believe I am seeing these pages, but have no instructions on how to calibrate them?
  9. Replies
    3
    Views
    46,413

    AOA Calibration on 5800

    The labels displayed when I run the AOA calibration on my 5800 are not the same as those on page 29 of the manual. Is there an updated calibration process? I have the Dynon heated Pitot/AOA....
  10. Replies
    3
    Views
    11,449

    Are there 2 Cal Points? Can I reset them to...

    Are there 2 Cal Points? Can I reset them to factory prior to the shift adjustment?
    Thanks,
    Frank
  11. Replies
    3
    Views
    11,449

    Manifold Pressure Sensor Calibration

    I can not find the MAP calibration process in the 5000 series manual, nor on a search of the forum.

    In the set up menu I think there are 2 value points?

    What is the process for the...
  12. Replies
    1
    Views
    8,532

    AFS/Dynon ADS-B with 4500

    Is the 4500 compatible with the AFS/Dynon ADS-B device? Will it than share the data with the 5800? Settings?
    Thanks
    Frank
  13. Thread: v12 Software

    by Frank D
    Replies
    12
    Views
    21,219

    Is there a link to the software download? My...

    Is there a link to the software download? My ADAHRS is giving me a Incorrect Firmware message when I search for devices.
    Thanks
    Frank
  14. Replies
    1
    Views
    10,438

    EGT and CHT Reading Errors

    I just fired up the new 5800 system with Engine Board. All of my sensors have been calibrated and are functioning, except EGT and CHT.

    The EGT and CHT readings are jumping around between 200 to...
  15. Thread: Component Pics

    by Frank D
    Replies
    2
    Views
    7,551

    Glenn, I have turbo cad or dxf files with many...

    Glenn, I have turbo cad or dxf files with many components. If you have that capability I can send a sample to you. I also have a Visio version for some components. email me if you would like me to...
  16. Ok, got it. I was referring to the drawing on...

    Ok, got it.

    I was referring to the drawing on page 293 of the manual that you had referenced in your answer. That one does not show the connection of the AF TXP to the GTN. It might be good to add...
  17. Rob, can I display TIS traffic on GTN? , should I...

    Rob, can I display TIS traffic on GTN? , should I also wire ...
    GTN-650>>>>AF Transponder
    P1001-26 >>> 7

    Or will the GTN get traffic from the connection to the 5800?
  18. Based on what I have read I was going to go with...

    Based on what I have read I was going to go with RS-232 Out 2 on the GTN, with setting as RS-232 2 In Off, Out ADS-B +

    GTN-650>>>>Transponder
    P1001-7 >>> 3
  19. Thanks Rob, but that drawing does not include a...

    Thanks Rob, but that drawing does not include a GTN - TXP connection. I did find the file below, which I downloaded yesterday but can't seem to find again. I will try this on the GTN Serial 2 Out....
  20. Thanks Rob, It looks like I should split the...

    Thanks Rob,

    It looks like I should split the RS 232 Out from a single output to two?
    GTN 650 Out 1 for AF 5800
    GTN 650 Out 2 for TXP Pin P1001-3 to TXP pin 3

    Thanks
    Frank
  21. GTN 650 RS -232 settings for AF TXP 261 and AF ADS-B

    Are the settings for the GTN 650 supposed to be?

    RS-232 1 In FADC Format 1, Out Aviation Output 1
    RS-232 2 In Off, Out ADS-B +
    RS-232 3 In Off. Out Off

    Is the Transponder setting 17. ADS-B...
  22. Replies
    3
    Views
    8,402

    Hi Rob, If I were to convert from SkyView to 5600...

    Hi Rob, If I were to convert from SkyView to 5600 and 5800 screens, will the Dynon ADAHRS, ADS-B etc. components be compatible?
    Thanks
    Frank
  23. Will the AF-2500 interface with 5000 Series EFIF

    Can the AF 2500 provide engine data to the 5000 series EFIS? I am trying to see if I can fit the larger screens into my panel without a complete remake...

    Thanks
    Frank
  24. Replies
    0
    Views
    7,482

    3500 Screen Going Flat Line

    I have had 2 instances where my 3500 EM screen has gone from normal to lined to dark in flight. The system will still feed engine data to my 4500s, but the screen goes totally unreadable. It worked...
  25. Replies
    1
    Views
    7,490

    Serial Port 3 External AHRS

    On page 46 of the 3500 Manual there is a Serial Port #3 function for Ext. AHRS - Dynon AHRS. Can I take the serial output from the D100 to function as a back up AHRS to my AFS boxes? Are there a...
Results 1 to 25 of 25