Search:

Type: Posts; User: Blain

Page 1 of 2 1 2

Search: Search took 0.01 seconds; generated 58 minute(s) ago.

  1. Thread: GPS to 406 ELT

    by Blain
    Replies
    1
    Views
    559

    GPS to 406 ELT

    Can the 4500 feed NMEA 1083 to the 406 from serial #3? If not I’m considering an inexpensive gps antenna using 5 volts. Can I use the 5v source from the expansion port?
  2. Replies
    2
    Views
    1,735

    Echo skyFYX for GPS source?

    Not sure what Echo uses for data protocol. Can I split the output and feed the 4500 or do I need a dedicated GPS?
  3. Replies
    4
    Views
    94,018

    Still curious. Shawn, Rob?

    Still curious. Shawn, Rob?
  4. Replies
    1
    Views
    3,968

    Magnetometer location

    Building a Just SuperStol. Wondering if wing location is better then fuselage for magnetometer. Fuse is steel tube while wing is all fabric and aluminum.
  5. Thread: AOA on SuperStol

    by Blain
    Replies
    1
    Views
    4,172

    AOA on SuperStol

    Building a Just SuperStol. Wondering if there is an AOA port location identified for this wing? It does have slats and spoilers.
  6. Replies
    1
    Views
    25,802

    Standby frequencies from 4500 to GTR 200

    Very little information describing how this should be configured. Just replaced an Icom A210 with GTR 200. Havern't found standby frequencies on either. I won't rule out a wiring issue.

    When does...
  7. Replies
    2
    Views
    76,485

    I’ve seen them twice. Next time up I’ll go over...

    I’ve seen them twice. Next time up I’ll go over the area. Can the 4500 save a screen shot?
  8. Replies
    2
    Views
    76,485

    Help with icon identification

    AFS 4500 with Uavionix. Noticed an icon that I don’t see in the users manual. It is a yellow ring maybe 1000’ in diameter. Not a yellow circle as only the boarder is yellow. Next to it is “SFC 15...
  9. Replies
    4
    Views
    94,018

    Filter or declutter

    Uavionix Echo into AFS4500. Any way to filter traffic? If I’m at 2500 and can see an airliner at FL 30 it is a distraction.
  10. Thread: AF-4500 FIS-B

    by Blain
    Replies
    3
    Views
    52,411

    I’ve done that. I get traffic but not showing...

    I’ve done that. I get traffic but not showing weather.
  11. Thread: AF-4500 FIS-B

    by Blain
    Replies
    3
    Views
    52,411

    AF-4500 FIS-B

    Should FIS-B display on my 4500 now?
  12. Thread: What is updated?

    by Blain
    Replies
    1
    Views
    10,956

    What is updated?

    I use the free update of aviation and obstacle database for my 4500. I always assumed it was the same updates as a sectional provides. Am I correct?
  13. Replies
    11
    Views
    21,413

    Verified. My report came back clean. And my N...

    Verified. My report came back clean. And my N numbers shows on the ghost.
  14. Replies
    11
    Views
    21,413

    Working with good performance report. But I’m...

    Working with good performance report. But I’m ghosting or seeing myself. Uavionics says I need to make sure my N number is programmed into the EFIS because that’s where the filtering takes place. I...
  15. Replies
    11
    Views
    21,413

    Installed EchoUAT, 4500, serial #3, pin #5, set...

    Installed EchoUAT, 4500, serial #3, pin #5, set serial as ADSB 115k, traffic displays on IPad. “About” shows (PID:0) Idle, TRFC:0, FIS-B:0, OSHIP:0
    Might be source config. Should it be GDL90 or...
  16. Thread: GPS source

    by Blain
    Replies
    1
    Views
    6,121

    GPS source

    Is the 73102 a compliant source for ADSB?
  17. Replies
    3
    Views
    7,984

    Any replacement options for Navworx on 4500?

    Prewired my 4500 for Navworx before the recent fiasco. Not sure I want to wait it out. I see a lot of new hardware in the market. Anything give us in and out in the same format Navworx offered?
  18. Replies
    13
    Views
    34,964

    The default preload for my RV-8 feels better then...

    The default preload for my RV-8 feels better then after the calibration. How can I load the settings listed above to get back to the factory configuration?
  19. Replies
    2
    Views
    8,296

    Saved me a lot of extra work. Thanks Shawn.

    Saved me a lot of extra work. Thanks Shawn.
  20. Replies
    2
    Views
    8,296

    4500 engine sensor harness

    Installing engine sensor harness. I did not group sensor wires with their respective ground terminals. Are all the grounds common or will I need to sort them out?
  21. Thread: wifi connection

    by Blain
    Replies
    3
    Views
    9,210

    Can this be used with the 4500?

    Can this be used with the 4500?
  22. Replies
    2
    Views
    12,845

    Thanks, Shawn. I'll verify they use the same.

    Thanks, Shawn. I'll verify they use the same.
  23. Replies
    2
    Views
    12,845

    Shunt interchange

    Have shunt used on Vans analog amp meter gage. Does it have the right value for my AFS 4500?
  24. Replies
    4
    Views
    15,358

    Just to verify, I'm removing a Insight-GEM 602...

    Just to verify, I'm removing a Insight-GEM 602 engine monitor and replacing with AFS 4500. GEM says they use Type "K for EGT and type "J" for CHT. The thermocouple will be compatible, correct?
  25. Replies
    1
    Views
    7,010

    Found it. Broken d-sub pin #19. Hope there aren't...

    Found it. Broken d-sub pin #19. Hope there aren't any more.
Results 1 to 25 of 33
Page 1 of 2 1 2